We replace the belt after 60 thousand km of vehicle mileage or four years of calendar service life.

Check the condition of the belt at every service.

The drive circuit of auxiliary units depends on the vehicle configuration, whether the air conditioner is installed on the vehicle or not.

The belt tension is adjusted by an automatic tensioner.

To check and replace the belt, we install the car on a viewing ditch or lift.

Install anti-roll shoes under the rear wheels. We put the car on the parking brake. Loosen the front right wheel bolts. Raise the front of the car and remove the right front wheel.

We remove the mudguard of the engine compartment (article - Removing the engine protection, wheel arch liners and mud flaps Renault Duster)

We unscrew the three self-tapping screws for attaching the wheel arch liner to the front bumper and one self-tapping screw for attaching the wheel arch liner to the fender.

Проверка и замена ремня вспомогательных агрегатов Renault DusterПроверка и замена ремня вспомогательных агрегатов Renault Duster

We bend the front part of the wheel arch liner and put it behind the brake disc.

With a head of 18, we turn the crankshaft by the bolt of the accessory drive pulley clockwise and inspect the belt along its entire length. If cracks or other defects are found on the belt, we replace the belt.

Replacing the rollers and the accessory drive belt on a 2.0 l engine

Проверка и замена ремня вспомогательных агрегатов Renault Duster

The belt installation diagram is shown in Figure 3.

Проверка и замена ремня вспомогательных агрегатов Renault DusterПроверка и замена ремня вспомогательных агрегатов Renault Duster

We put a 16 spanner wrench on the hexagon of the tensioner and turn the roller bracket clockwise

Remove the belt from the pulleys and remove the belt from the engine compartment

Marking of the drive belt for auxiliary units with air conditioning 7РК 1792

Проверка и замена ремня вспомогательных агрегатов Renault Duster

Belt length 1792 mm.

To replace the belt support roller:

Проверка и замена ремня вспомогательных агрегатов Renault DusterПроверка и замена ремня вспомогательных агрегатов Renault Duster

With a 13 head, unscrew the roller mounting bolt

We remove the roller with the bolt of its fastening

Проверка и замена ремня вспомогательных агрегатов Renault Duster

We take out the bolt and the roller cover from the roller

Проверка и замена ремня вспомогательных агрегатов Renault Duster

By rotating the roller, we determine the condition of the bearing

The roller should rotate silently, evenly, without jamming.

To replace the tensioner roller:

Проверка и замена ремня вспомогательных агрегатов Renault DusterПроверка и замена ремня вспомогательных агрегатов Renault Duster

Using the TorxT40 wrench, unscrew the roller fastening screw

Remove the tension roller and roller cover

If necessary, remove the tensioner for this:

Проверка и замена ремня вспомогательных агрегатов Renault DusterПроверка и замена ремня вспомогательных агрегатов Renault Duster

With a 16 head, unscrew the tensioner mounting bolt

Remove the tensioner assembly with the roller

When installing the tensioner, the protrusion 1 on the tensioner must fit into the groove 2 of the accessory mounting bracket.

Проверка и замена ремня вспомогательных агрегатов Renault Duster

We install all the details in reverse order. We install the belt in accordance with the diagram in Figure 3.

Replacing the rollers and the accessory drive belt on the 1.6 l engine

Marking of the accessory drive belt for the K4M 6PK 1822 engine with air conditioning.

Проверка и замена ремня вспомогательных агрегатов Renault Duster

We loosen the belt tension, put on a 15 key or a 15 head on the tension roller bolt from the bottom of the car.

Проверка и замена ремня вспомогательных агрегатов Renault DusterПроверка и замена ремня вспомогательных агрегатов Renault Duster

Turn the roller bracket clockwise and loosen the belt

Remove the belt from the support roller

Проверка и замена ремня вспомогательных агрегатов Renault DusterПроверка и замена ремня вспомогательных агрегатов Renault Duster

Remove the accessory drive belt from the pulleys

To remove the support roller, unscrew the bolt of its fastening with a spanner wrench

Проверка и замена ремня вспомогательных агрегатов Renault DusterПроверка и замена ремня вспомогательных агрегатов Renault Duster

Remove the outer roller cover

Remove the support roller

Проверка и замена ремня вспомогательных агрегатов Renault DusterПроверка и замена ремня вспомогательных агрегатов Renault Duster

Removing the inner cover

To remove the tensioner with a 10 head, unscrew two bolts

Remove the tensioner assembly with the roller

Проверка и замена ремня вспомогательных агрегатов Renault Duster

Install all parts in reverse order.

We put the belt on the pulleys, and start it under the tension and support rollers in accordance with the diagram.