On cars, block headlights are used that combine a two-filament low and high beam lamp, a side light lamp and a direction indicator lamp
The so-called transparent glass optics are used in the headlights.
The headlight cover is absolutely smooth and does not perform the function of distributing light fluxes. It is made of plastic that is more transparent and lighter than a glass cover.
A layer of protective varnish protects it from minor damage (scratches).
The direction indicators built into the headlights are made without color filters, instead lamps with glass of a certain color are used.
Fog lights
In the variant version, the cars are equipped with fog lamps installed in the lower part of the front bumper.
The fog lights can only be turned on with the steering column switch when the exterior lights are on.
Rear lights
The lamps, made in a modern style, have transparent shades for direction indicators and reversing lights.
The rear fog light bulb is installed in the left tail light.
The fog lamp can only be turned on with the steering column switch when the exterior lights are on.
Indicators
Turn signal lamps are installed in the headlights, rear and side lights.
The direction indicators are switched on by the left stalk switch (lamps on one side, depending on the position of the switch) or the hazard warning switch (all lamps at the same time).
Headlight Corrector
In a variant version, the cars are equipped with a headlight beam corrector, which allows you to change the direction of the headlight beam in the vertical plane depending on the load of the car.
Replacing bulbs in the headlight unit
To replace the bulbs in the headlight unit, open the hood and disconnect the negative battery terminal
Disconnect the wiring harness from the dipped/high beam lamp
Remove headlight cover
Remove the spring retainer from the hooks on the reflector
Let's fold back the lamp cap
Removing the low/high beam lamp
We install a new lamp - H4 60/55 A. We fix the lamp with a spring clip, install the cover and connect the wire block.
Replacing the parking light bulb
Turn the side light bulb holder clockwise
We remove the cartridge with the side light lamp from the headlight housing
Remove the baseless lamp from the socket
Insert the new W5W parking light bulb into the socket and install it in place
Replacing the turn signal bulb
We press the retainer of the turn signal lamp wire block
Remove the block of wires
Turn the direction indicator lamp socket counterclockwise and remove it from the headlight
Click on the lamp and turn it counterclockwise, remove it from the cartridge
Install the new PY21W lamp in reverse order
Replacing the turn signal lamp
We pull the turn signal lamp towards ourselves, overcoming the force of the clamps, we take it out of the wing hole
Disconnect the socket with the lamp by turning it counterclockwise
Removing the baseless lamp.
We install a new WY5W lamp and install the turn signal lamp in the reverse order.
Replacing a bulb in a car taillight
To replace the lamps in the rear light, you need to remove the light, to do this, disconnect the negative battery terminal
Remove the upholstery of the trunk from the side of the removed lamp
Unscrew the plastic nut of the rear light
Retrieve the lantern to the length of the attached wires
Pressing on the latch, disconnect the block of wires from the rear light
Remove the rear light
Remove the soundproofing pad from the lantern
Press the latches with your fingers
Remove the back cover lantern assembly with lamp sockets
Slightly pressing the lamp that needs to be replaced into the cartridge, turn it counterclockwise and remove it from the cartridge
When installing a new lamp, the protrusions on the lamp must fit into the slots on the socket.
Then we fix the lamp in the socket by turning it 90˚ clockwise.
Install the parts in reverse order.
Replacing the license plate light
Disconnect the negative battery terminal
Prying on the retainer
Remove the license plate light
Turn the lamp socket clockwise by 90˚
Remove the socket with the lamp
Remove the baseless lamp from the socket
Install the new W5W lamp in reverse order.
Replacing a lamp in an additional brake light
Disconnect the negative battery terminal
Press the two tabs
Remove the casing of the additional signal
To replace the lamp, press the cartridge lock down
Turn the lamp socket clockwise
Remove the cartridge with the lamp from the signal housing
Pull out the lamp and remove it from the socket
Install the new P21W lamp in reverse order.
Changing the bulb in the interior light
Disconnect the negative battery terminal
Pry off the cover diffuser with a flat screwdriver
Remove diffuser
Remove the lamp from the socket
Insert a new W5W lamp and install a diffuser
Replacing the cigarette lighter bulb
Remove the cigarette lighter cartridge and remove the LED
Having prying with a screwdriver, disconnect the housing of the cigarette lighter lamp socket from the LED
Spreading the edges of the case
Slide and remove the lamp socket
Remove the lamp from the socket and replace it
