We replace sensors and switches when they fail.

Removing the emergency oil pressure drop sensor

Replacing sensors and switches on a Renault Sandero

The sensor is installed at the rear of the cylinder block on the right side, next to the engine number.

Preparing the car for the task.

Disconnect the negative battery terminal.

Replacement of Renault Sandero car sensors and switchesReplacing sensors and switches on Renault Sandero

Disconnect the wire block from the sensor

Weaken the sensor with the key 22

Replacing sensors and switches on Renault SanderoReplacing sensors and switches on Renault Sandero

Unscrew the sensor from the cylinder block

The sensor is sealed with a copper or aluminum washer

Install the sensor in reverse order.

Replacing the fuel gauge sensor

Fuel level sensor installed in fuel pump module

Preparing the car for the task. We relieve the fuel pressure in the fuel line (described in the article - Checking the fuel pressure of a Renault Sandero car)

After that, disconnect the negative battery terminal

Remove the fuel pump module

Replacing sensors and switches on a Renault SanderoReplacing sensors and switches on Renault Sandero

Disconnect the fuel level sensor wire block from the module cover

Disconnect the fuel pump wiring harness

Replacing sensors and switches on a Renault SanderoReplacing sensors and switches on a Renault Sandero

Push the screwdriver on the latch and move the sensor up

Remove the fuel level sensor

Install parts in reverse order

Reversing light switch replacement

The reverse light switch is mounted on the gearbox near the left front wheel drive

We prepare the car and disconnect the negative battery terminal

Replacing sensors and switches on Renault Sandero

Press the wire block retainer

Replacing sensors and switches on Renault SanderoReplacing sensors and switches on Renault Sandero

Disconnect the wire block from the switch

Weaken the keys by 24 tightening and unscrew the reverse light switch from the gearbox housing

Install the switch in reverse order.

Apply thread lock sealant to the threads of the switch.

Replacing and adjusting the brake light switch

Replacement of Renault Sandero car sensors and switches

The switch is mounted on the bracket of the pedal assembly

Disconnect the negative battery terminal

Replacement of Renault Sandero car sensors and switchesReplacing sensors and switches for Renault Sandero

We press the latches and disconnect the wire block from the brake light switch

Turn the switch 90˚

Replacement of Renault Sandero car sensors and switchesReplacing sensors and switches on Renault Sandero

Remove the switch

To adjust, pull out the switch stem (clicks will be heard)

Install the switch in reverse order

Replacement of Renault Sandero car sensors and switches

We press the pedal a little, and insert a plate approximately 2 mm thick and pull the pedal up (clicks will be heard).

We take out the plate and check the operation of the brake lights; when the pedal is released, the brake lights should not light.

Choose the pedal free play.

The brake lights should come on when the pedal is moved within the free play.

Replacing the parking brake off warning light switch

Replacing sensors and switches on Renault Sandero

Remove the parking brake lever (for this operation, see the article - Renault Sandero Parking Brake Repair)

You can replace the parking brake switch without removing the drive lever, you just need to remove the lining of the floor tunnel, but of course it is more convenient to do this with the lever removed.

Replacement of Renault Sandero car sensors and switchesReplacing sensors and switches on Renault Sandero

We unscrew the screw securing the switch

Remove the parking brake switch

Install all parts in reverse order

Replacing interior light switches

Disconnect the negative battery terminal

Replacement of Renault Sandero car sensors and switchesReplacing sensors and switches on Renault Sandero

Remove the protective cap from the switch

We press the latches with a screwdriver and remove the switch from the hole in the body

Replacement of Renault Sandero car sensors and switchesReplacing sensors and switches on Renault Sandero

Disconnecting the wire block

Remove the switch. Install the switch in reverse order.

Replacing instrument panel switches

Replacing interior light switches Replacing interior light switches

Remove the plug of the radio socket

Disconnect the pads from the plug and the antenna wire or remove the radio

Replacing interior light switches Replacing interior light switches

Pry off the cover with a screwdriver

Remove the center trim

Replacing interior light switchesReplacing interior light switches

Remove the latch and disconnect the switch pads from the switch

Remove the latches and remove the switches from the central trim

Install parts in reverse order

Removing and installing the antenna

Replacing interior light switches Replacing interior light switches

Unscrew the antenna from the bracket by turning counterclockwise

Remove the antenna. Install the antenna in reverse order

Removing and installing engine control sensors for a Renault / Dacia Sandero car, see the article - Replacing the components of the Renault Sandero engine control system