The car uses a speed control system to help the driver not exceed the set speed of the car
Controlling the speed limiter
- 1 - main switch "On / off";
- 2 - a reminder of the saved speed limit value and a step increase in the speed limit (RES / +);
- 3 - activation, memorization and stepwise decrease of the speed limit value (SET/-);
- 4 - put the system into standby mode (with storing the value of the speed limit) (0).
Enable speed limiter
Press switch 1 from the side (
)
Warning light 6 lights up orange and, depending on the vehicle, the message "LIMIT" appears on the instrument panel or the LIMIT warning light comes on together with dashes.
This means that the speed limiter is enabled and is waiting to enter and save the speed limit value
To save the current speed value as the set speed limit, press switch 3 (SET/-): instead of dashes, the speed limit value will appear.
The minimum value that can be memorized is 30 km/h
Driving a car with a speed limit set
When a speed value is memorized, the vehicle is steered in the same way as a vehicle without a speed limiter until the vehicle speed is equal to the set speed value
After the speed reaches the memorized speed, any action on the gas pedal will not allow you to exceed the speed, except in emergency cases
Change the speed limit value
You can change the set limiter speed by pressing:
- - button 2 (RES/+) to increase speed;
- - button 3 (SET/-) to decrease the speed
Please note that the speed limit function does not affect the vehicle's braking system
If the speed limiter does not turn on (after several attempts to turn it on), you need to contact an authorized dealer
Speed limit exceeded
At any moment, you can exceed the speed limiter value by pressing the accelerator (gas) pedal sharply and all the way
During the overspeed time, the vehicle's set speed limit flashes on the instrument panel
Then we release the accelerator (gas) pedal: the previously selected speed mode will be restored as soon as the vehicle speed is lower than the previously set speed value
Cases where the limiter cannot maintain the given rate limit
When the car is accelerating on a steep descent, the system is unable to keep the speed at the set speed limit:
- when the limit is exceeded, the set speed limit value flashes on the instrument panel and, depending on the vehicle configuration, a sound signal is emitted regularly, informing about this situation.
Putting the system to standby
Speed limiter action is suspended when switch 4 (0) is pressed
In this case, the speed limit value is stored in the memory and, depending on the vehicle equipment, the message "MEM" appears on the instrument panel or the MEM lamp lights up along with the display of the saved speed value
Retrieving a saved speed limit
If a speed limit value has been memorized, it can be recalled by pressing switch 2 (RES/+) once
When the speed limiter is in standby mode, pressing switch 3 (SET/-) will reactivate the speed limiter, but the previously stored speed limit value will not be taken into account.
The system will take the current vehicle speed as the new limit
system shutdown
If you press switch 1, the speed limit mode will be canceled without saving the speed limit value.
Orange warning light () on the instrument panel goes out, confirming that the system has been switched off
Drive speed controller
Cruise control is a function that keeps the vehicle moving at the speed you set; this speed is called variable speed
The set speed of the vehicle maintained by the speed controller must be greater than 30 km/h.
This system is an additional tool that makes driving easier
Do not use the cruise control in heavy traffic, on winding or slippery roads, or in adverse weather conditions
Controls
- 1 - main switch "On / off";
- 2 - reminder of the saved speed value and increase the speed to the set one (RES / +);
- 3 - switch to enable, remember and reduce the set speed (SET/-);
- 4 – switching the system to standby mode (with storing the value of the set speed) (0).
Enable
Press switch 1 from the side (
)
Warning light 6 lights up green and (depending on vehicle equipment) the message "CRUISE" appears on the instrument panel or the CRUISE warning light comes on together with a dash.
This indicates that the speed controller is ready to enter a set speed
Enabling speed controller
When the current vehicle speed is stable (above 30 km/h), press switch 3 (SET/-): the function is activated and the current speed is memorized
Instead of dashes, the cruise control setpoint is displayed and cruise control activation is confirmed by the message (depending on the vehicle) "CRUISE" or the CRUISE lamp turning on, and the green lamp 5 turning on (
) and signal lamp 6 ()
Driving a car
After memorizing the speed setpoint and turning on the speed controller, you can release the accelerator (gas) pedal
It should be noted that when driving a car, the feet should be close to the pedals in order to quickly react in a dangerous situation
Changing the set value of vehicle speed
You can change the set speed by pressing the buttons in sequence:
- - button 2 (RES/+) to increase speed;
- - button 3 (SET/-) to decrease the speed
Exceeding the speed supported by the speed controller
The set speed can be exceeded at any time by pressing the accelerator pedal
While the speed is exceeded, the vehicle speed value set for the cruise control system flashes on the instrument panel
Release the accelerator (gas) pedal: after a few seconds, the car will automatically return to the initial set speed
Cases when the regulator cannot maintain the given speed limit
When driving on a steep incline or uphill, speed control is not supported by the system:
- in this case, the set speed value flashes on the instrument panel, informing about it
Putting the system to standby
The function goes to standby when pressed:
- -switch 4 (0);
- - brake pedal;
- - Clutch pedal or put the lever in the neutral position for a car with an automatic transmission.
In these 3 cases, and depending on the vehicle, the variable speed setpoint is stored in memory and the message "MEM" appears on the instrument panel or the MEM warning light comes on
Switching the speed controller function to o mode waiting is confirmed by turning off the signal light ()
Recalling the set vehicle speed
The saved variable speed value can be called up by activating the system if road conditions are favorable for driving at a constant speed
If the vehicle speed is above 30 km/h, press switch 2 (RES/+).
When recalling a speed value, turning on the speed controller is confirmed by turning on the signal lamp ()
Note:
- if the previously recorded speed is significantly higher than the current speed, the car will start accelerating sharply until it reaches the set limit
When the speed control is in standby mode, pressing the 3 (SET/-) button will reactivate the function, but without saving the previously set speed.
The current vehicle speed is now taken into account as the regulated speed
Shutting down the system
When switch 1 is clicked () the cruise control is deactivated
In this case, the speed value is no longer stored in memory.
Turn off two signal lights () and () on the instrument panel confirms the deactivation of the function
Putting the cruise control function to standby or disabling it does not result in a rapid reduction in driving speed.
To brake, press the brake pedal.
